Hubbardton-forge 307910 Manual do Utilizador descarregar pdf

Installation Instructions B136

For Airis Sconce 30-7910 Page 1 of 3

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21155 Rev F

To Install Fixture (Figures 1 & 2)

Component Parts

A Crossbar

B 8-32 x 1” Screw

C Fixture

D 8-32 x 3/8” Screw (2)

E Mounting Bracket

F #10 x 1” Screws (2)

G Caulking Lip

H Screw

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided) attach crossbar (A) to the

electric box. Note: A new electric box comes with screws. When

replacing a fixture, retain the screws for use with the new fixture.

3. From center hole of crossbar measure down 13-3/16" and mark location

for first hole for wall mounting bracket (E). Be sure hole location is

vertical to center hole of crossbar (A).

4. Hold mounting bracket (E) so hole matches location marked previously

and mark bottom hole location.

5. Attach mounting bracket (E) using #10 x 1" screws (F).

6. Loosen screws (D) so they do not protrude through edge of mounting bracket (E)

at this time. Note: Screws are shipped installed in bracket.

7. Install screw (H) in tab on bottom of fixture (C). Screw should only be installed a

couple of turns at this time (Figure 2).

8. Using suitable wire connectors (not provided), connect the fixture wires to the

supply wires, (white to white, white to black, bare copper or green to bare copper

or green).

Caution: Make sure wire connectors are twisted on securely and no bare wires

are exposed.

9. Apply a generous bead of a suitable caulking material to caulking lip (G) on the

fixture (Figure 2).

10. Carefully tuck all wires behind the fixture, align bottom of fixture with mounting

bracket (E), place fixture firmly against the wall and fasten with 8-32 x 1" screw

(B). To ensure a water tight seal, apply a thin bead of caulking around entire

perimeter of the fixture.

11. Tighten screw (D) on both sides of mounting bracket (E) until snug against fixture.

12. Install light bulb (not provided).

13. See installation instructions below for option purchased.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 2)

(Figure 1)

1 2 3

B136 1
21155 Rev F 1

Resumo do Conteúdo

Página 1 - 21155 Rev F

Installation Instructions B136 For Airis Sconce 30-7910 Page 1 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route

Página 2

Installation Instructions B136 For Airis Sconce 30-7910 Page 2 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route

Página 3

Installation Instructions B136 For Airis Sconce 30-7910 Page 3 of 3 Hand-Forged, Vermont-Made Lighting and Accessories P.O. Box 827, 154 Route

Comentários a estes Manuais

Sem comentários

Hubbardton-forge 307910 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Iluminação Hubbardton-forge 307910. Hubbardton Forge 307910 User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Iluminação Hubbardton-forge 307910