Hubbardton-forge 207875 Manual do Utilizador descarregar pdf

Installation & Assembly Instructions B118

For Exos Wave Wall Sconce 20-7875 Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19873 Rev B

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Install Fixture (Figure 1)

Component Parts

A Wall Mount Bracket

B Anchors (6)

C #10 Screws (6)

D Fixture

E #8 Black Screws (6)

F Green Ground Screw

G Cupped Washer

H Outside Wall Mount Bracket

Caution: Be sure power is off at the main

breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (A) over the

electrical box being sure to hold it plum

and level. With a pencil, mark the location

of all mounting holes in the wall mount

bracket on the wall behind. Measure up 1

3/8” from center of the wall mount bracket

and out 16” to locate outside wall mount

bracket locations. Mark center location of

both outside wall mount bracket (H).

IMPORTANT: Wall mount bracket must be

secured to a solidly mounted electrical box

and/or a framing member in at least two

locations. Do not depend on drywall

anchors alone to support this fixture. If in

doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,

place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight

hammer.

(Figure 1)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

e noted on fixture. Use onl

recommended bulbs with fixture.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (C), screw the brackets securely to the wall. Be careful not to over-tighten

or strip the anchors.

4. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare copper or

green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail

lead to the bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

1 2

B118 1
19873 Rev B 1

Resumo do Conteúdo

Página 1 - 19873 Rev B

Installation & Assembly Instructions B118 For Exos Wave Wall Sconce 20-7875 Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessories

Página 2

Installation & Assembly Instructions B118 For Exos Wave Wall Sconce 20-7875 Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessories

Comentários a estes Manuais

Sem comentários

Hubbardton-forge 207875 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Iluminação Hubbardton-forge 207875. Hubbardton Forge 207875 User Manual Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Iluminação Hubbardton-forge 207875